Sawmill for Sale

To include: MIC Trimmer Line:  16' trim saw, with 0 saw, will pass a 20' board, includes infeed singulator transfer, Softac scanners and software, evenender rolls, movable fence, push button console, all controls in control office, 30'x30" waste conveyor under trimmer, (2) hyd. packs on ground under trimmer, trimmer controls attached, supports to the floor, conveyor & transfer, no motor controls. New stack cylinder in box. MIC 10' Tall 4 Dual Chain Bar Type Haul Up Unscrambler: MIC 10' Tall 4 Dual Chain Bar Type Haul Up Unscrambler  

Hour meter shows 6431Hrs. 3phase main power. 120v Motor Controllers. 15HP 3phase Hydraulic unit. Set up for 1 1/2" bands. Self-tensioning blade system uses air power for blade tension. Comes with operators cab. Cab has heat and air. Joystick controls and computer set works. Comes w/ approx. 30 new Wood-Mizer 739 blades. Ready to work. Needs nothing. Will be removed and ready to set on your trailer. Located in Salem, IN. For further details, please contact Tyler Pence (270)766-4184. $55,000

20HP 3 Phase 12" x 17' infeed belt w/ 12" x 17' return belt. Set up for 2 inch bands. Comes with Hydraulic unit. Was used for staves but can remove diverters and used for lumber again. Located in New Haven, KY 40051. Contact Tyler Pence for further details (270)766-4184 $9,000

15" 3 Strand log infeed deck with stop and load. Bar chain log turner. 56" circle saw on husk frame. 150 HP electric motor. On board hydraulic power pack. 20' outfeed belt conveyor. Located at 120 Commercial Dr., Edmonton, KY 42129. Call Tyler Pence for more information: 270-766-4184 $60,000

Model 36D-1433A-91. movable saws. 4" edger. Located at 120 Commercial Dr., Edmonton, KY 42129. Call Tyler Pence for more information: 270-766-4184 $8,500

60" wide. 536hp CAT engine. 24" capacity. 200 gallon fuel capacity. 120 gallon hydraulic capacity. Total weight is 48,000lbs. Length is 47.5" Machine is still under warranty with 1800 hours. Located in Moultrie, GA. Contact Ethan for more info 931-607-4738 $330,000

100hp 3ph motor with shaker table. Located in Big Clifty, KY. Contact Tyler for more info 270-766-4184 $27,500

Shop built. No motor. Located at 120 Commercial Dr., Edmonton, KY 42129. Call Tyler Pence for more information: 270-766-4184 $11,000

12in x 12in throat capacity. 16ft max cut length. Full run around system. 25HP 3 Phase motor. Self contained Hydraulic pump and tank. Set up for 1 1/2” bands. Pre-programable digital set works. 12volt set works. Ready to work. Will be removed and ready to set in your trailer. Located in Salem, IN. For further details, contact Tyler Pence (270)766-4184 $13,200

25HP 3phase motor. Accuset Controls. Shows 6455 hours. Comes w/ axle and tires. Cable track needs repair. Located in New Haven, KY 40051. Contact Tyler Pence for further details (270)766-4184 $19,000

Includes 8' 4 strand infeed deck, hydraulic power pack, and 6' 6 strand outfeed deck. Located at 3471 Brown Road, Valdosta, GA 31601. Call Ethan for details: 931-607-4738 $38,500

SN: 202, 50 HP motor, self contained hydraulic system. 10 HP hydraulic pack. Located at 3471 Brown Road, Valdosta, GA 31601.  8% sales tax applies. Call Ethan for details: 931-607-4738 $11,000

Located at 3471 Brown Road, Valdosta, GA 31601. Call Ethan for details: 931-607-4738 $45,000

Barko 160A W/ CTR Ground Saw. Lever controls. Starts Easy and Runs Strong. 4cyl John Deere Turbo engine. Hour meter shows 803 hrs. Professionally line bored and re-pinned main boom bushing and stick boom bushing. Very dry machine. Window unit and inverter for A/C. Comes with replacements for all cylinders, swing motors, and main pump. Comes with extra grapple. All 8 tires are in good shape on Pitts Trailer. On the job working now. Located in Mt Sherman, KY. For further details, contact Tyler Pence (270)766-4184 $22,000

LOG INFEED: Hourglass Roll case, 18' long x 22" rolls 66" OAL 8" OD on end 5" OD in middle. Stop and load with 3 kickers. MORBARK DEBARKER: (E48SCS) stamped on frame. BARN SWEEP UNDER DEBARKER: 30' flat x 48" wide 14" paddles, 24' incline section x 40" wide. Located in Warrensburg, NY. Contact Ethan for more details 931-607-4738. $15,000

LOG INFEED DECK TO CARRIAGE: 3 strand 10' wide x 22' long, Stop and load with 3 kickers. Electrical on infeed wall. Barn sweep under saw. Laser lights. Forrest-All Modular Mill with 54" saw, chain turner, 2 saw vertical edger, (2) spare saws, 4 HB carriage 14' long, knee spacing is 54" - 39" - 39" , Track 46' long 45" track spacing, Off-bearer belt 16' x 18' Track 46' long, 45" track width, 44' flat x 48" wide 10' incline 15" paddles, Computer Setworks for carriage and Vertical Edger. Spare saws (1) 54", (3) 48", (4) 50"   Located in Warrensburg, NY. Contact Ethan for more info 931-607-4738  $30,000

SPIRAL ROLLCASE: 18' x 24' with 7" rolls LANDING TABLE: 14' x 4' with 5 dead rolls HILLTOP TRIMSAW: Two saw with 20" saws Located in Warrensburg, NY. Contact Ethan for more info 931-607-4738 $8,000

4-strand 40' long x 12' wide, 48' - 42" - 48" , (11'8" OAL) Located in Warrensburg, NY. Contact Ethan for more info 931-607-4738 $5,000

BELT CONVEYOR TO CHIPPER: 20' x 18", 5 Dead Rolls for cant transfer to slides (above belt conveyor) MORBARK CHIPPER WITH CHIP PAC: 3 Knife, 3ph/75HP motor, with dual chip loader  CHIP BLOWER: Approximately 20' of 8" pipe FINES BLOWER: Approximately 10'' of 6" pipe Located in Warrensburg, NY. Contact Ethan for more info 931-607-4738  $30,000